This hopefully fixes intermittent initrd failures where udevd cannot
create a Unix domain socket:
machine# running udev...
machine# error getting socket: Address family not supported by protocol
machine# error initializing udev control socket
machine# error getting socket: Address family not supported by protocol
The "unix" kernel module is supposed to be loaded automatically, and
clearly that works most of the time, but maybe there is a race
somewhere. In any case, no sane person would run a kernel without Unix
domain sockets, so we may as well make it builtin.
http://hydra.nixos.org/build/30001448
(cherry picked from commit e4b4e9b986)
Previously this barfed with:
updating GRUB 2 menu...
fileparse(): need a valid pathname at /nix/store/zldbbngl0f8g5iv4rslygxwp0dbg1624-install-grub.pl line 391.
warning: error(s) occured while switching to the new configuration
(cherry picked from commit 1ba2015450)
This hopefully fixes intermittent test failures like
http://hydra.nixos.org/build/29962437
router# [ 240.128835] INFO: task mke2fs:99 blocked for more than 120 seconds.
router# [ 240.130135] Not tainted 3.18.25 #1-NixOS
router# [ 240.131110] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
assuming that these are caused by high load on the host.
(cherry picked from commit 6d02d7e740)
... because we make it built-in by default.
I can't imagine anyone who wanted to purge this module from his/her system,
so let's keep it simple, at least for now.
(cherry picked from commit 0e1fe66aad)
This change should "only" get rid of an annoying error in logs.
$d should be $sd, this causes resume from hibernate to fail if
resumeDevice is not explicitly set in config. Introduced in commit:
'stage-1: Shut up warnings about swap devices that don't exist yet'
When using extlinux-conf-builder in a nix build using chroots, the
following error message could be seen:
/nix/store/XXX-extlinux-conf-builder.sh: line 121: cd: /nix/var/nix/profiles: No such file or directory
To avoid this, just skip the code path parsing /nix/var/nix/profiles
when $numGenerations (passed from the command line) is 0 (which is the
only legal value of $numGenerations in a nix build context).
Without a menu title, U-Boot's distro scripts just autoboot the first
entry by default.
When I initially wrote this, my board wasn't apparently running stock
U-Boot but had some local hacks saved in the U-Boot's environment
which made it always display the prompt.
When calling addEntry inside a subshell, the filesCopied array would
be updated only in the subshell's environment. This would only cause an
issue if no -g flag was passed to the script, causing no kernels
to be copied.
This fixes a failing assert in systemd-timesyncd (issue #5913) as it
expects the directory /run/systemd/netif/links/ to exist, and nothing in
NixOS currently creates it.
Also we get a net reduction in our code as rules for /run/utmp and
/var/log/journal are also provided by the same upstream file.
(cherry picked from commit a278a9224a)
This shuts up this error from dbus:
May 11 13:52:16 machine dbus-daemon[259]: Unknown username "systemd-network" in message bus configuration file
May 11 13:52:16 machine dbus-daemon[259]: Unknown username "systemd-resolve" in message bus configuration file
which happens because the D-Bus config for networkd/resolved is
enabled unconditionally, and we don't have an easy way to turn it off.
(cherry picked from commit f19b58fb6a)
Some filesystems like fat32 don't support symlinking and need to be
supported on /boot as an efi system partition. Instead of creating the symlink directly in boot, create the symlink in
a temporary directory which has to support symlinking.
This solves the problem that modprobe does not know about $MODULE_DIR
when run via sudo, and instead wrongly tries to read /lib/modules/:
$ sudo strace -efile modprobe foo |& grep modules
open("/lib/modules/3.14.37/modules.softdep", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory)
open("/lib/modules/3.14.37/modules.dep.bin", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory)
open("/lib/modules/3.14.37/modules.dep.bin", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory)
open("/lib/modules/3.14.37/modules.alias.bin", O_RDONLY|O_CLOEXEC) = -1 ENOENT (No such file or directory)
Without this patch, one would have to use sudo -E (preserves environment
vars). But that option is reserved for sudo users with extra rights
(SETENV), so it's not a solution.
environment.sessionVariables are set by PAM, so they are included in the
environment used by sudo.
