Draft Wire/de

Draft Wire
Menüeintrag
Draft -> Wire
Arbeitsbereich
Draft, Arch
Standardtastenkürzel
W I
Siehe auch
Draft Line, Draft BSpline
Contents 1 Draft Wire 2 Beschreibung und Anwendung 3 Options 4 Properties 5 Scripting

Beschreibung und Anwendung

Mit diesem Werkzeug wird ein aus geraden Stücken zusammen gesetzter Linienzug erzeugt. Dieser unterscheidet sich von der einfachen Geraden (Line) lediglich durch die Vielzahl von geraden Stücken.

Letztes Linienstück beenden:

1. Nach Erzeugen des letzten Punkts die F- oder die C-Taste drücken oder
2. Doppelklicken beim Erzeugen des letzten Punkts.

.

Options

• If several connected Draft Lines are selected when pressing the Draft Wire Button, they will be turned into a wire and the command will exit. available in version 0.17

• Press F or the Finish button to finish the wire, leaving it open
• Press C or the Close button or click on the first point to finish the wire, but making it closed by adding a last segment between the last point and the first one.
• Press X, Y or Z after a point to constrain the next point on the given axis.
• To enter coordinates manually, simply enter the numbers, then press ENTER between each X, Y and Z component.
• Press R or click the checkbox to check/uncheck the Relative button. If relative mode is on, the coordinates of the next point are relative to the last one. If not, they are absolute, taken from the (0,0,0) origin point.
• Press T or click the checkbox to check/uncheck the Continue button. If continue mode is on, the Wire tool will restart after you finish or close it, allowing you to draw another one without pressing the Wire button again.
• Press CTRL while drawing to force snapping your point to the nearest snap location, independently of the distance.
• Press SHIFT while drawing to constrain your next point horizontally or vertically in relation to the last one.
• Press W or press the Wipe button to remove the existing segments and start the wire from the last point.
• Press CTRL+Z or press the Undo button to undo the last point.
• Press I or the Filled button to have the wire filled with a face if it is closed.
• Press ESC or the Cancel button to abort the current Line command.
• Closed wires, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.

Properties

• DATAClosed: Specifies if the wire is closed or not
• DATAChamfer Size: Specifies the size of chamfered corners
• DATAFillet Radius: Specifies a curvature radius to give to the nodes of the wire
• DATASubdivisions: Divides the segments of the wire with the given number of subdivisions available in version 0.16

• DATAMake Face: Fills the wire with a face if it is closed
• VIEWEnd Arrow: Shows an arrow symbol at the last point of the wire, so it can be used as an annotation leader line
• VIEWPattern: Specifies a hatch pattern to fill the wire with (Closed Wire)
• VIEWPattern Size: Specifies the size of the hatch pattern

See also Draft Pattern page.

Scripting

The Wire tool can by used in macros and from the python console by using the following function:

makeWire (list or Part.Wire, [closed], [placement], [facemode]) 

• Creates a Wire object from the given list of vectors or from the given wire.
  • If closed is True or if first and last points are identical, the wire is closed.
  • If facemode is True (and the wire is closed), the wire will appear filled.
• The current Draft linewidth and color will be used.
• Returns the newly created object.

Beispiel:

import FreeCAD,Draft
p1 = FreeCAD.Vector(0,0,0)
p2 = FreeCAD.Vector(1,1,0)
p3 = FreeCAD.Vector(2,0,0)
Draft.makeWire([p1,p2,p3],closed=True)